Workshops & Tools

66 topics in this forum

1. How to heat a freezing workshop? 1 2 3

   By Jon Matcho, December 19, 2004
   • 63 replies
   • 9,202 views
   • 
   • Jon Matcho
   • August 18, 2020

3. Dust Control

   By TDubs74, July 25, 2020
   • 5 replies
   • 303 views
   • 
   • TDubs74
   • August 1, 2020

4. Heating the workshop

   By vezePilot, November 7, 2019
   • 1 reply
   • 271 views
   • 
   • jridge
   • November 7, 2019

5. Dremel Bit 502

   By Jon Matcho, August 27, 2018
   • 2 replies
   • 536 views
   • 
   • Jon Matcho
   • August 28, 2018

6. Put everything on wheels!

   By Jon Matcho, July 24, 2018
   • 15 replies
   • 562 views
   • 
   • Jon Matcho
   • August 24, 2018

7. Auto-controlled Epoxy Hot-box Upgrade

   By Voidhawk9, July 30, 2018
   • 1 reply
   • 329 views
   • 
   • Jon Matcho
   • July 31, 2018

8. Vacuum bagging

   By aereform, December 27, 2009
   • 4 replies
   • 1,348 views
   • 
   • aereform
   • January 5, 2010

9. garage door size

   By jpolenek, November 29, 2009
   • 5 replies
   • 1,042 views
   • 
   • steve
   • November 29, 2009

10. Setting up the shop

    By Crazycanuck, September 21, 2009
    • 16 replies
    • 1,571 views
    • 
    • aviator_edb
    • November 16, 2009

11. Homemade forced air respirator

    By cozybldr, November 11, 2009
    • 6 replies
    • 1,780 views
    • 
    • schmeddz
    • November 11, 2009

12. Epoxy scales

    By Ryan D., October 2, 2009
    • 2 replies
    • 1,039 views
    • 
    • SpaceShipOne
    • October 3, 2009

13. Michaels Engineering Ratio Pump

    By SpaceShipOne, September 26, 2009
    • 6 replies
    • 1,172 views
    • 
    • Kraig
    • September 28, 2009

14. Fein knockoff at Harbor Freight $49.99 1 2

    By Cozy1200, November 9, 2008
    • 31 replies
    • 7,546 views
    • 
    • longezdave
    • September 22, 2009

15. DIY Autoclave

    By ColinB, June 24, 2009
    • 22 replies
    • 10,209 views
    • 
    • airnico
    • June 27, 2009

16. Cheap treat for Melbournites

    By daveb, May 16, 2009
    • 1 reply
    • 1,017 views
    • 
    • Lifessamsara
    • May 16, 2009

17. 8 foot long Aluminum Straight edges

    By Windwalker, April 30, 2009
    • 2 replies
    • 1,371 views
    • 
    • Cozy1200
    • April 30, 2009

18. Where do you build? 1 2

    By mlefebvre, January 1, 2004
    • 30 replies
    • 5,281 views
    • 
    • mfryer
    • April 23, 2009

19. just wing-en it !

    By steve, February 20, 2009
    • 11 replies
    • 1,488 views
    • 
    • steve
    • March 8, 2009

20. How long do your Fein Blades last??

    By GuinnessGuy74, February 19, 2009
    • 15 replies
    • 1,909 views
    • 
    • CBarber
    • March 6, 2009

21. How hot can it get?

    By TMann, January 15, 2009
    • 16 replies
    • 1,839 views
    • 
    • DemonFrog
    • February 20, 2009

22. Table complete!!

    By flybeech21, December 22, 2008
    • 8 replies
    • 1,503 views
    • 
    • Cozy Girrrl
    • December 24, 2008

23. Itch, itch, itch ........ 1 2

    By TMann, December 11, 2008
    • 26 replies
    • 2,800 views
    • 
    • Spodman
    • December 21, 2008

24. Basement Door....

    By flybeech21, December 8, 2008
    • 17 replies
    • 2,316 views
    • 
    • TMann
    • December 18, 2008

25. EC Cutter (Dritz Scissor copy) - YMEN Aust 1 2

    By Spodman, March 28, 2008
    • 37 replies
    • 4,682 views
    • 
    • Spodman
    • October 25, 2008

26. Fein Multimaster Substitute?

    By GuinnessGuy74, October 14, 2008
    • 0 replies
    • 1,540 views
    • 
    • GuinnessGuy74
    • October 14, 2008