flybeech21 Posted December 8, 2008 Share Posted December 8, 2008 I have a question about where I am going to build the Aerocanard FG. I have a very large basement that will work just fine. But, there is only a single garage door going into the basement. It is an 8' X 7' garage door. Will I be able to get the 11' wide completed fuselage out of that door by "turning it through the door?" Do I need to consider building in the basement and assembling elsewhere? Thanks, Kevin Harper Atlanta, GA Quote Link to comment Share on other sites More sharing options...
NeilK Posted December 9, 2008 Share Posted December 9, 2008 Not according to Autocad. (testing attachments) Quote Link to comment Share on other sites More sharing options...
TMann Posted December 9, 2008 Share Posted December 9, 2008 I think you could get it out. Worst case you would have to leave one strake unfinished until you move to a larger location. I'm building a Long-EZ in my basement and can do it all but one strake there and still get it through the double door entry. It just depends og whether or not you have the room inside that will allow you to start it out withe the unfinished strake side and pivot it around. It's a 3D kind of solution. Quote T Mann - Loooong-EZ/20B Infinity R/G Chpts 18 Velocity/RG N951TM Mann's Airplane Factory We add rocket's to everything! 4, 5, 6, 7, 8. 9, 10, 14, 19, 20 Done Link to comment Share on other sites More sharing options...
rickh Posted December 9, 2008 Share Posted December 9, 2008 What Tom sez. If you have clear space either side of the door, poke one spar end through, swivel the tub a bit, shove the fuse out. Once the strakes are built, all bets are off. Rick Quote Rick Hall; MK-IV plans #1477; cozy.zggtr.org Build status: 1-7, bits of 8-9, 10, 14 done! Working on engine/prop/avionics. Link to comment Share on other sites More sharing options...
Big Steve Posted December 9, 2008 Share Posted December 9, 2008 What do you think concrete saws were made for??? Steve build on Quote Steve Harmon Lovin Life in Idaho Cozy IV Plans #1466 N232CZ http://websites.expercraft.com/bigsteve/ Working on Chapter 19,21 Link to comment Share on other sites More sharing options...
TMann Posted December 9, 2008 Share Posted December 9, 2008 What do you think concrete saws were made for???SAY AMEN SOMEBODY!!!!!! Quote T Mann - Loooong-EZ/20B Infinity R/G Chpts 18 Velocity/RG N951TM Mann's Airplane Factory We add rocket's to everything! 4, 5, 6, 7, 8. 9, 10, 14, 19, 20 Done Link to comment Share on other sites More sharing options...
rickh Posted December 9, 2008 Share Posted December 9, 2008 AMEN! I remember a Steve Parkins shop pix a while back. I noticed it was two *single* car overhead doors... Rick Quote Rick Hall; MK-IV plans #1477; cozy.zggtr.org Build status: 1-7, bits of 8-9, 10, 14 done! Working on engine/prop/avionics. Link to comment Share on other sites More sharing options...
TMann Posted December 9, 2008 Share Posted December 9, 2008 I can't remember who it was ....... but someone lived in an area that had a covenent stating you had to have two single doors vs. one double. They got anound it by putting in a removeable center pilar. Very clever. Quote T Mann - Loooong-EZ/20B Infinity R/G Chpts 18 Velocity/RG N951TM Mann's Airplane Factory We add rocket's to everything! 4, 5, 6, 7, 8. 9, 10, 14, 19, 20 Done Link to comment Share on other sites More sharing options...
Big Steve Posted December 9, 2008 Share Posted December 9, 2008 I dont remeber where I saw it but it was a picture of a eze type being taken out the kitchen floor so they could get it out of the basement. That is what I call either dedication or really bad planning. STeve build on Quote Steve Harmon Lovin Life in Idaho Cozy IV Plans #1466 N232CZ http://websites.expercraft.com/bigsteve/ Working on Chapter 19,21 Link to comment Share on other sites More sharing options...
steve Posted December 9, 2008 Share Posted December 9, 2008 AMEN! I remember a Steve Parkins shop pix a while back. I noticed it was two *single* car overhead doors... Rick had it been a stock cozy it would have fit. i missed it by 4".you need to lift one strake up to the top corner, with the nose low and the other strake low. put the nose in then the top strike then roll it around the small of the lower strake. the cc strake or the smp-cc strake will not fit. but you can easily open your door,remove the lower track, 2by10 and then put it though the opening with the cc strike . look at the pic and you can see the room i lost, the wood is laying about stock . good to here someone starting on a dream Quote Steve M. Parkins Link to comment Share on other sites More sharing options...
ErlendM Posted December 9, 2008 Share Posted December 9, 2008 What do you think concrete saws were made for??? Steve build on Like this guy who built his own Lamborghini Countach in his basement - without any doors at all... The story is here: http://www.telegraph.co.uk/motoring/3382143/Man-digs-under-house-to-remove-home-made-Lamborghini.html Quote Erlend Moen Norway Cozy MK IV #1556 - Chapter 16http://cozy.ljosnes.no Link to comment Share on other sites More sharing options...
Big Steve Posted December 9, 2008 Share Posted December 9, 2008 The previous post proves that where there is a will there is a way. STeve build on Quote Steve Harmon Lovin Life in Idaho Cozy IV Plans #1466 N232CZ http://websites.expercraft.com/bigsteve/ Working on Chapter 19,21 Link to comment Share on other sites More sharing options...
Edge 513 Posted December 9, 2008 Share Posted December 9, 2008 Steve- Hey, whats a cc strake? Got me on that one? Quote Self confessed Wingnut. Now think about it...wouldn't you rather LIVE your life, rather than watch someone else's, on Reality T.V.? Get up off that couch!!! =) Progress; Fuselage on all three, with outside and inside nearly complete. 8 inch extended nose. FHC done. Canard finished. ERacer wings done with blended winglets. IO540 starting rebuild. Mounting Spar. Starting strake ribs. Link to comment Share on other sites More sharing options...
Cozy1200 Posted December 10, 2008 Share Posted December 10, 2008 hmm. I seem to recall this being done with a cozy.... http://forum.canardaviation.com/showthread.php?t=511&highlight=basement Quote Drew Chaplin (aka the Foam Whisperer) --- www.Cozy1200.com - I'm a builder now! --- Brace for impact... Link to comment Share on other sites More sharing options...
steve Posted December 10, 2008 Share Posted December 10, 2008 Steve- Hey, whats a cc strake? Got me on that one? cozy girls, sorry i ment cg stake and smp/cg strake Quote Steve M. Parkins Link to comment Share on other sites More sharing options...
Neverquit Posted December 17, 2008 Share Posted December 17, 2008 If the basement door is a 8' x 7' door as stated, it CAN be done with any cutting. Here's a way I've taken the project out and in the garage 3 times already. This was my first attempt by myself. Note the chain hanging on the left of the photo. This is from a chain fall tied to a radiator in the upstairs bedroom. At this point I was on the phone calling the troops. Mr. Lefleur brought over his son and his buddies. We had it out in ten minutes. Other times Mr. Skorija and his buddy came over. Note: use three to four young men and supervise instead of three old coots. Would have been a cinch if the limestone block post in between the doors was removed. Unfortunately it was not an option if I wanted to keep the upstairs bedroom in one piece. Quote Link to comment Share on other sites More sharing options...
Hennie Engelbrecht Posted December 18, 2008 Share Posted December 18, 2008 This guy has done it.... Hennie Quote Link to comment Share on other sites More sharing options...
TMann Posted December 18, 2008 Share Posted December 18, 2008 If the basement door is a 8' x 7' door as stated, it CAN be done with any cutting. NICE Retracts! Quote T Mann - Loooong-EZ/20B Infinity R/G Chpts 18 Velocity/RG N951TM Mann's Airplane Factory We add rocket's to everything! 4, 5, 6, 7, 8. 9, 10, 14, 19, 20 Done Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.