HiGeez Posted July 27, 2008 Share Posted July 27, 2008 Everyone: Started on my wing with the cores supplied by Eureka (Steve). Warning abt this product. I was a piece of... ...absolutly perfectly cut cores. Unless you need the core-cutting fix, Eureka is highly recommended. They were near perfect. No wire drag marks, corners square, parts matched up, etc. What else can I say. Good job Steve. With the Cozy Girl's parts & Steves's cores, there is no excuse now for not finishing. Jerry Preiser Quote Jerry Preiser - HiGeez Link to comment Share on other sites More sharing options...
gullikson Posted July 28, 2008 Share Posted July 28, 2008 Glad to hear the the good news about Eureka cores. I am going to order a set for my Long-EZ in the next couple weeks or so. Quote Link to comment Share on other sites More sharing options...
mfryer Posted July 28, 2008 Share Posted July 28, 2008 I just sent a check to Steve for canard cores. Now the wait will be even worse for me. Thanks a lot!!! Quote Link to comment Share on other sites More sharing options...
EZ AHAB Posted July 29, 2008 Share Posted July 29, 2008 Man, you scared me for a minute:yikes: I guess it pays to read more than the first line. Thanks Jerry! Good luck on your project. Please keep me up to speed on your progress. I'm at Oshkosh right now. Burrall Sanders from Freeflight Composites, the Cozy Girrrls, and myself have a booth right in front of Hangar A (where Nat used to be). We are here for ACS supporting the Cozy Mk IV with our "Cozy Builders Group" booth. Stop by and say hi. I have some small examples of my work, the CGs have a bunch of beautiful metal parts, and Burrall has his new Cozy III sporting a really cool glass panel. God Bless, Steve James Quote EUREKA CNC Extreme Precision CNC Hotwire Cutting http://www.eurekacnc.com Perfection To The Core! Link to comment Share on other sites More sharing options...
Phil Kriley Posted July 29, 2008 Share Posted July 29, 2008 Steve's product support is second to none as well! Quote Phil Kriley Cozy #1460 Chapter 13 - nose Right wing done - working on right winglet. Link to comment Share on other sites More sharing options...
Beastus_Maximus Posted July 30, 2008 Share Posted July 30, 2008 Man, you scared me for a minute:yikes: I guess it pays to read more than the first line. Thanks Jerry! Good luck on your project. Please keep me up to speed on your progress. I'm at Oshkosh right now. Burrall Sanders from Freeflight Composites, the Cozy Girrrls, and myself have a booth right in front of Hangar A (where Nat used to be). We are here for ACS supporting the Cozy Mk IV with our "Cozy Builders Group" booth. Stop by and say hi. I have some small examples of my work, the CGs have a bunch of beautiful metal parts, and Burrall has his new Cozy III sporting a really cool glass panel. God Bless, Steve James The bad news is.... your website is so not working right now Quote We make no mistakes, ONLY INNOVATIONS! Link to comment Share on other sites More sharing options...
EZ AHAB Posted July 31, 2008 Share Posted July 31, 2008 Ok, after an attack from some Australian viagra salesmen:irked: :irked: , I think the site is back up and operational:D . Let me know if you have any further problems. If you have my site as a favorite, it might not work any more because I had to change some of the filename structure around. The link below should work at any rate, however. -Steve Quote EUREKA CNC Extreme Precision CNC Hotwire Cutting http://www.eurekacnc.com Perfection To The Core! Link to comment Share on other sites More sharing options...
Beastus_Maximus Posted July 31, 2008 Share Posted July 31, 2008 Sent you a PM Quote We make no mistakes, ONLY INNOVATIONS! Link to comment Share on other sites More sharing options...
mfryer Posted August 10, 2008 Share Posted August 10, 2008 FedEX dropped of my Long-EZ cores today and they are awsome, I highly recommend them.. Unfortunatly I cannot say the same for FedEX: The box arrived with a scary gash in the side. All was not lost thought as the damage was minor and easily repaired. Quote Link to comment Share on other sites More sharing options...
Phil Kriley Posted August 11, 2008 Share Posted August 11, 2008 Yes, FedEx can do a real number on foam. They got to buy a new set of cores for me. Looks like they placed the box across two other boxes and then dropped a drive-shaft on it! Notice the smooth "dent" next to the break. Steve did a great job of getting a replacement pair sent out, with warnings and lables all over the box - made it unscathed! Quote Phil Kriley Cozy #1460 Chapter 13 - nose Right wing done - working on right winglet. Link to comment Share on other sites More sharing options...
mfryer Posted August 12, 2008 Share Posted August 12, 2008 Yes, FedEx can do a real number on foam. They got to buy a new set of cores for me. Looks like they placed the box across two other boxes and then dropped a drive-shaft on it! Notice the smooth "dent" next to the break. Steve did a great job of getting a replacement pair sent out, with warnings and lables all over the box - made it unscathed! Wow! I feel lucky after looking at that. The damage to my cores was limited to less than 1" of a corner of one aileron. I micro'd the damaged piece back in place and all is well. Overall I am very happy with the cores and I plan on ordering a set of wings when the time comes. Quote Link to comment Share on other sites More sharing options...
Phil Kriley Posted August 12, 2008 Share Posted August 12, 2008 Overall I am very happy with the cores and I plan on ordering a set of wings when the time comes. I second that! Quote Phil Kriley Cozy #1460 Chapter 13 - nose Right wing done - working on right winglet. Link to comment Share on other sites More sharing options...
EZ AHAB Posted August 12, 2008 Share Posted August 12, 2008 In general I've had very good luck with FedEx although there have been a few occasions where there has been damage. The cores come packed in the blocks they are cut from so they are very well protected but foam isn't all that sturdy and can be easily damaged if mishandled. This is especially true of the elevators which are very fragile. The good new is that I always insure everything I ship through them so, if there is damage, they will pay for it. In the past I've had good luck with getting them to pay up for the damage they've caused. In Phil's case they bought him a new set of elevators and paid to ship them. Quote EUREKA CNC Extreme Precision CNC Hotwire Cutting http://www.eurekacnc.com Perfection To The Core! Link to comment Share on other sites More sharing options...
Cozy Girrrl Posted August 13, 2008 Share Posted August 13, 2008 Ok, after an attack from some Australian viagra salesmen:irked: :irked: , I think the site is back up and operational:D . Let me know if you have any further problems. If you have my site as a favorite, it might not work any more because I had to change some of the filename structure around. The link below should work at any rate, however. -Steve Maybe they desperately need Viagra down under?...Chrissi (used to be blond) Quote CG Products www.CozyGirrrl.com Cozy Mk-IV RG 13B Turbo Link to comment Share on other sites More sharing options...
EZ AHAB Posted January 2, 2009 Share Posted January 2, 2009 I've recently gotten orders to move again. Gotta love active duty; I don't think I've lived in the same place for more than 3.5 years since 1990. Anyway, I'm going to take orders through Jan 09 or until I have all I can handle before the move. After that all orders will be on hold. I plan on starting back up again when I get settled in but, due to training requirements, moving, setup, etc it will probably be Aug-Sept 09 at the earliest. See my website for more details or to make an order. Quote EUREKA CNC Extreme Precision CNC Hotwire Cutting http://www.eurekacnc.com Perfection To The Core! Link to comment Share on other sites More sharing options...
Spodman Posted January 2, 2009 Share Posted January 2, 2009 Maybe they desperately need Viagra down underThere was a police spokesman who is a regular on a radio station reporting on a break in at a pharmacy here a while ago. They took a crate of Viagra. The spokesman said they would be looking for some hardened criminals... The damage to my cores was limited to less than 1" of a corner of one aileron.I hope you're not going to put the ailerons on the canard:confused: Quote Mark Spedding - SpodmanDarraweit Guim - AustraliaCozy IV #1331 - Chapter 09www.mykitlog.com/Spodmanwww.sites.google.com/site/thespodplane/the-spodplane Link to comment Share on other sites More sharing options...
Cozy Girrrl Posted January 2, 2009 Share Posted January 2, 2009 Congratulations Steve! Let us know how we can help you while you're busy. ...Chrissi & Randi Quote CG Products www.CozyGirrrl.com Cozy Mk-IV RG 13B Turbo Link to comment Share on other sites More sharing options...
EZ AHAB Posted January 2, 2009 Share Posted January 2, 2009 Thanks gals, you two have been a tremendous help already I suppose you could take a road trip and help me pack That invitation is open to the rest of you as well! Quote EUREKA CNC Extreme Precision CNC Hotwire Cutting http://www.eurekacnc.com Perfection To The Core! Link to comment Share on other sites More sharing options...
Cozy Girrrl Posted January 2, 2009 Share Posted January 2, 2009 Maybe you could cut all of your foam and ship it to Dennis and let him ship it? ...Chrissi & Randi Quote CG Products www.CozyGirrrl.com Cozy Mk-IV RG 13B Turbo Link to comment Share on other sites More sharing options...
EZ AHAB Posted January 2, 2009 Share Posted January 2, 2009 Just wanted to point out that the order deadline is the end of Jan 2009, not the 9th of Jan as could be misconstrued from my earlier post. Quote EUREKA CNC Extreme Precision CNC Hotwire Cutting http://www.eurekacnc.com Perfection To The Core! Link to comment Share on other sites More sharing options...
EZ AHAB Posted January 2, 2009 Share Posted January 2, 2009 Maybe you could cut all of your foam and ship it to Dennis and let him ship it? ...Chrissi & Randi I thought about doing something like this. It would cost too much to mail it to anyone first but I could probably find someone to ship for me that is here in the Abilene area. I may try to cut a few extra to have in stock but the limiting factor is my available time. After working on the house to get it ready to sell, packing, house hunting trips, etc, not to mention my day job; there's not much of it left. Quote EUREKA CNC Extreme Precision CNC Hotwire Cutting http://www.eurekacnc.com Perfection To The Core! Link to comment Share on other sites More sharing options...
Cozy Girrrl Posted January 2, 2009 Share Posted January 2, 2009 Steve, Maybe someone up in the Ft Worth area...lots of Canardians up there? ...Chrissi Quote CG Products www.CozyGirrrl.com Cozy Mk-IV RG 13B Turbo Link to comment Share on other sites More sharing options...
HiGeez Posted January 2, 2009 Author Share Posted January 2, 2009 Steve, Good luck on your move. Ex Airforce myself. C ya when you return. Wings (Eureka supplies), winglets done. Anybody listening? Great product, you will not be disapointed with Eureka! Jerry HiGeez Preiser Quote Jerry Preiser - HiGeez Link to comment Share on other sites More sharing options...
mfryer Posted January 3, 2009 Share Posted January 3, 2009 There was a police spokesman who is a regular on a radio station reporting on a break in at a pharmacy here a while ago. They took a crate of Viagra. The spokesman said they would be looking for some hardened criminals... I hope you're not going to put the ailerons on the canard:confused: It only took me a second to make that mistake, why so long for you to correct me (thanks)? Anyhow the damage to the ELEVATOR, was eventually trimmed off anyhow because the cores come a little long. All is well. Quote Link to comment Share on other sites More sharing options...
EZ AHAB Posted February 3, 2009 Share Posted February 3, 2009 Still taking a few more orders on a conditional basis. See my website for details. If you are the Airbus pilot from Germany that called me on the 20th of Jan, please call or email me if you still want to order. Quote EUREKA CNC Extreme Precision CNC Hotwire Cutting http://www.eurekacnc.com Perfection To The Core! Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.